الاثنين، 12 أغسطس 2013

Gold Claimer Concentrator





The Gold Claimer Concentrator is self contained, and with its 2-8 yd/hr capacity, it is ideal for
testing gold values or for small production operations.  It’s performance is unequalled to any in
its field.  The unique water supply and reclamation unit allows operation where water is not
available.  

Efficiency is a key ingredient!  The hopper has an adjustable water valve to slurry the material
prior to entering the trommel.  Lifters tumble the material as it enters the trommel to break it up.
A spray bar with its own adjustable water valve goes the length of the trommel.  Next, the
material approaches the 3/8” holes where anything under 3/8” gets washed down onto the
oscillating sluice, and larger material works its way to the end of the trommel.  A nugget trap will
catch any heavies and the lighter material will go out the tail cone to the rock chute and discard
tray.  The oscillating sluice has settings for stationary, short, & long strokes and is capable of 1-
15 pulses per minute.  The removable sluice has artificial turf, riffles mounted on expanded metal
& 4 toggles to secure it into place.  Any light material that gets washed off the sluice goes into
the de-watering screw.

The de-watering screw is the most efficient way to remove solids from water and recirculate the
water.  The auger is raised from the bottom which allows for a black sand trap & a second
recovery for the gold in case too much water flows over the sluice.  The de-watering screw has
an adjustable water valve located on the bottom to help the heavy material settle & lighter
material to auger out.  Waste material will auger out & discard at the end of the Gold Claimer.

Using the de-watering screw is the most efficient way to remove solids from the water &
recirculate it.  The auger is raised from the bottom allowing the black sands to trap & a second
recovery for gold in case of too much water over the sluice.  The adjustable water valve located
on the bottom helps the heavy material too settle & lighter material to auger out.  Waste material
augers out and discards at the end of the Gold Claimer.  When plenty of water is available & you
don’t need to recirculate the water, remove the de-watering screw by removing 2 bolts and the
drive shaft.  The only change needed is to remove the intake hose off the pump and place a
longer hose with a foot valve in your water source.

The unique design of the Gold Claimer makes the clean up process easy!  At the end of the day
(or sooner if needed), disengage the clutch or shut off motor.  At the hopper end of the unit,
slide the sluice out of its cradle by the handle.  Put it over a tub, lift the 4 toggles & slide the
riffles & artificial turf out to be washed.  Reinstall the carpet and riffles, slide the unit back into
the sluice cradle & start the operation once again.  Another option is to have a second complete
sluice ready.

The Gold Claimer recirculates approximately 100 gallons of water .  You may need to add a little
water due to evaporation and the wetness of the waste material.  Drain plugs are in both the
water tank and the de-watering screw.

The simplicity of the Gold Claimer makes it the leader in the field of small portable placer
equipment.  Industrially built, it is easy to maintain & powered by either an electric or gasoline
engine.  Either one uses the same motor mount which is easily removable by removing the snap
pin & sliding out the motor mount.  It was designed that way so you can easily take it with you at
the end of the day to cut down on theft.  One motor runs both the gear reducer & water pump
using a B-Width belt.  The trommel is a positive chain drive.

The Gold Claimer is uniquely designed for its versatility!  The trommel itself can act like a rod mill
by placing two 30" 1 1/4 rod.  It will help break up clay if that is a problem where you are
operating.  You can also double your capacity by placing two Gold Claimers hopper to hopper
and adding a "splitter", then feeding both units with our
12' Feed Conveyor
.

Gold Claimer Specifications



Water feed valves for Trommel and Hopper feed control  

Revolving Scrubber and Trommel with positive chain drive  

Removable Oscillating Sluice (150 impulses/minute)  

Teel cast iron 3950 G.P.H. Water Pump  

Variable speed single belt drive for simplicity and reliability  

100 gallon capacity reserve water storage tank  

Auger style De-watering Screw  

13 GA Steel construction made for industrial use  

Sealed Steel Bearings

8'L x 5'6"W x 4'6"H @ 850 lbs.

Capacity 2 to 8 cubic yards per hour  

Trailer mounted with lights, fenders and 4.80 wheels

Honda Engine


ليست هناك تعليقات:

إرسال تعليق